|
|||||||||||||||
|
|||||||||||||||
|
|||||||||||||||
![]() |
*ORIGINAL MANUAL SPECIFICATIONS*
TOTAL MACHINE
Length, approx ...........................18000mm 59'
Depth below floor approx .................4200mm 13'9in
Height above floor approx. ...............8100mm 26'7in
Width, approx ............................6400mm 21'
WORKING RANGES
Rolling Speed, Main Roll (Nominal Dia)....0.4-1.6 m/s 1.3 - 5.2 ft/s
Max. Radial Rolling Force.................4000 kN 450 short tons
Peak, Max.................................4500 kN 500 short tons
Max Axial Rolling Force...................2000 kN 220 short tons
MAIN ROLL
Nominal Outside Diameter..................1000 mm 39-37 in
Max, Main Roll Dia for Profiled Rings.....1400 mm 55 in
Max. Height of Main Roll
Above Rolling Plane..................950 mm 37 in
Below Rolling Plane..................80 mm 3 in
Height of Standard Main Roll, max.
Above Rolling Plane..................950 mm 37 in
Below Rolling Plane..................30 mm 1 in
AXIAL ROLLS
Useable Length............................850 mm 33 in
Angle of cone.............................35 degrees
MANDREL
Mandrel diameter at Max. roling force.....310 mm 12.2 in
Mandrel Outside Diameter..................200 mm 8 in
Max. Rolling Force........................1100 mm 120 short tons
ROLLING TABLE
Max. opening in the table ...................400mm 16in
Segment inserts for Max. mandrel diameter.....310mm 12.2in
With special table plates (not included in scope of delivery)
opening in the table Max. ....................500mm 20in
Max. Mandrel diameter ........................787mm 31in
Height of rolling table above floor...........500mm 20in
DATA OF FINISHED RING (when cold)
Ring outside diameter ........................600-3 600mm 24-141in
Max ring outside diameter (only side removal from machine possible) ... 4400mm
173 in
Ring height ..................................60-900mm 2-35in
INTERNAL DIMENSIONS OF BLANK
Inside diameter= mandrel outside diameter+ ...50mm 2in
Max height ...................................900mm 35in
ADJUSTMENT PATHS
Max. Horizontal adjustment of upper and lower mandrel side... 100mm 39in
Mandrel bearing, upper, can be lowered by ....400mm 16in
Min. diameter between main roll and mandrel centre lines.... 640mm 25in
Axial frame, Horizontal .....................3600mm 142in
Upper axial roll, Vertical ..................890mm 35in
Max. distance between the axial rolls .......950mm 37in
Vertical adjustment ranges referred to the upper edge of the
lower axial roll:
Main roll ..... +10mm +0.5in
Mandrel ....... +10mm +0.5in
Rolling Table . -10mm -0.5in
Mandrel pivoting ............................+20mm 1in
Laser, Top ..................................900-950mm 8.7-37in
POWER RATING
Radical drive (DC) .......................2 x 500kw 670hp
Axial Drive (DC) .........................2 x 315kw 420hp
Hydraulic (AC) .........................350kw 470hp
WEIGHTS OF THE INDIVIDUAL SUB-ASSEMBLIES
The specified weights are only intended as guidelines
SUB-ASSEMBLY: APPROX. WEIGHT:
Entire Machine .................................. 220000 kg
Mandrel adjustment, raise/lower ................. 24000 kg
Main Drive .................................. 10000 kg
Centring Arm, each .............................. 4500 kg
Axial Frame & axial slide without gearbox and motor 41000 kg
Lower axial-roll and bearing .................... 3500 kg
Lower axial-roll motor .......................... 1400 kg
Lower axial-roll gearbox ........................ 5500 kg
Upper axial-roll and bearing .................... 3500 kg
Upper axial-roll motor .......................... 1400 kg
Upper axial-roll gearbox ........................ 5500 kg
Axial frame, positioning cylinder ............... 2000 kg
Rolling table, each side ........................ 1400 kg
RETURN
to complete inventory display
RETURN
to our home page